Pd-Cu/γ-Al2O3催化苯乙炔选择性加氢反应

引用本文: 王沾祺, 周志明, 张锐, 李莉, 程振民. Pd-Cu/γ-Al₂O₃催化苯乙炔选择性加氢反应[J]. 物理化学学报, 2014, 30(12): 2315-2322. doi: 10.3866/PKU.WHXB201410152 shu

Citation: WANG Zhan-Qi, ZHOU Zhi-Ming, ZHANG Rui, LI Li, CHENG Zhen-Min. Selective Hydrogenation of Phenylacetylene over Pd-Cu/γ-Al₂O₃ Catalysts[J]. Acta Physico-Chimica Sinica, 2014, 30(12): 2315-2322. doi: 10.3866/PKU.WHXB201410152 shu

Pd-Cu/γ-Al₂O₃催化苯乙炔选择性加氢反应

王沾祺 ^1, ,
周志明 ^1, ,
张锐 ^2, ,
李莉 ^3, ,
程振民 ^1,

基金项目:
教育部新世纪优秀人才支持计划(NCET-13-0801) (NCET-13-0801)

中央高校基本科研业务费(222201313011)资助 (222201313011)

摘要:

为了提高苯乙炔加氢反应中的苯乙烯选择性, 本文采用“胶体-等体积浸渍”两步法制备了Pd-Cu/γ-Al₂O₃双金属催化剂. 利用高分辨率透射电镜(HRTEM)、X射线光电子能谱(XPS)、CO脉冲化学吸附、N2物理吸附、电感耦合等离子体原子发射光谱(ICP-AES)等技术表征了Pd-Cu/γ-Al₂O₃的结构性质, 考察了Cu/Pd 摩尔比、Pd负载量以及金属引入顺序对Pd-Cu/γ-Al₂O₃催化苯乙炔选择性加氢性能的影响. 结果表明, 与Pd/γ-Al₂O₃单金属催化剂相比, Pd-Cu/γ-Al₂O₃的苯乙烯选择性大幅度提高, 尤其是当Pd负载量为0.3%(w), 且Cu/Pd摩尔比为0.6时, Pd-Cu/γ-Al₂O₃表现出优异的加氢选择性; 在0.1 MPa和40 ℃下, 当苯乙炔转化率为90%时, 双金属催化剂的苯乙烯选择性可达95%; 当转化率达到99%以上时, 苯乙烯选择性仍保持在82%左右. 分析表明, Pd-Cu/γ-Al₂O₃中形成了Pd-Cu合金, 但是两种金属间不存在电子转移, Cu对Pd的几何效应才是导致Pd-Cu/γ-Al₂O₃苯乙烯选择性增加的主要原因.

关键词:

English

Selective Hydrogenation of Phenylacetylene over Pd-Cu/γ-Al₂O₃ Catalysts

1.
1. State Key Laboratory of Chemical Engineering, East China University of Science and Technology, Shanghai 200237, P. R. China;
2. Engineering Research Center of Large Scale Reactor Engineering and Technology, Ministry of Education, East China University of Science and Technology, Shanghai 200237, P. R. China;
3. Institute of Chemical Engineering, East China University of Science and Technology, Shanghai 200237, P. R. China
Received Date: 20 August 2014
Available Online: 27 November 2014
Fund Project:
教育部新世纪优秀人才支持计划(NCET-13-0801)

中央高校基本科研业务费(222201313011)资助

Abstract:

A two-step method combining colloid synthesis and incipient wetness impregnation was developed for the preparation of bimetallic Pd-Cu/γ-Al₂O₃ catalysts, with the aim of increasing the selectivity to styrene in the selective hydrogenation of phenylacetylene. The structural properties of the catalysts were characterized using high-resolution transmission electron microscopy (HRTEM), X-ray photoelectron spectroscopy (XPS), CO-pulse chemisorption, N₂ physisorption, and inductively coupled plasma atomic emission spectrometry (ICPAES). The effects of changing the Cu/Pd molar ratio, the Pd loading, and the order in which the Pd and Cu were introduced into the catalysts on the catalytic activity and selectivity were investigated. The results showed that Pd-Cu/γ-Al₂O₃ exhibited much higher selectivity toward styrene than Pd/γ-Al₂O₃. In particular, Pd-Cu/γ-Al₂O₃ with a Pd loading of 0.3%(w) and a Cu/Pd molar ratio of 0.6 displayed excellent performance at 40℃under 0.1 MPa H₂, with a high selectivity of 95% at a conversion of 90%, and a selectivity of approximately 82%, even at conversions of higher than 99%. The increased selectivity of Pd-Cu/γ- Al₂O₃ was ascribed mainly to the geometrical effects of the Pd-Cu bimetallic alloys, rather than the electronic effects, since no electron transfer occurred between Pd and Cu.

Key words:

1. [1]
  
  (1) Galobardes, M.; Maurer, B. R. Selective Hydrogenation of Phenylacetylene in the Presence of Styrene. U.S. Patent 4822936, 1989-04-18.
  (1) Galobardes, M.; Maurer, B. R. Selective Hydrogenation of Phenylacetylene in the Presence of Styrene. U.S. Patent 4822936, 1989-04-18.
2. [2]
  (2) Xiao, J.; Yang,W.; Chen, Y. H.; Chen, X. H. Ind. Catal. 2004, 12, 7. [肖剑, 杨伟, 陈祎华, 陈秀宏. 工业催化, 2004, 12, 7.](2) Xiao, J.; Yang,W.; Chen, Y. H.; Chen, X. H. Ind. Catal. 2004, 12, 7. [肖剑, 杨伟, 陈祎华, 陈秀宏. 工业催化, 2004, 12, 7.]
3. [3]
  (3) Li, C.; Shao, Z.; Pang, M.;Williams, C. T.; Liang, C. Catal. Today 2012, 186, 69. doi: 10.1016/j.cattod.2011.09.005(3) Li, C.; Shao, Z.; Pang, M.;Williams, C. T.; Liang, C. Catal. Today 2012, 186, 69. doi: 10.1016/j.cattod.2011.09.005
4. [4]
  (4) Panpranot, J.; Phandinthong, K.; Sirikajorn, T.; Arai, M.; Praserthdam, P. J. Mol. Catal. A: Chem. 2007, 261, 29. doi: 10.1016/j.molcata.2006.07.053(4) Panpranot, J.; Phandinthong, K.; Sirikajorn, T.; Arai, M.; Praserthdam, P. J. Mol. Catal. A: Chem. 2007, 261, 29. doi: 10.1016/j.molcata.2006.07.053
5. [5]
  (5) Na-Chiangmai, C.; Tiengchad, N.; Kittisakmontree, P.; Mekasuwandumrong, O.; Powell, J.; Panpranot, J. Catal. Lett. 2011, 141, 1149. doi: 10.1007/s10562-011-0593-3(5) Na-Chiangmai, C.; Tiengchad, N.; Kittisakmontree, P.; Mekasuwandumrong, O.; Powell, J.; Panpranot, J. Catal. Lett. 2011, 141, 1149. doi: 10.1007/s10562-011-0593-3
6. [6]
  (6) Hu, J.; Zhou, Z.; Zhang, R.; Li, L.; Cheng, Z. J. Mol. Catal. A: Chem. 2014, 381, 61. doi: 10.1016/j.molcata.2013.10.008(6) Hu, J.; Zhou, Z.; Zhang, R.; Li, L.; Cheng, Z. J. Mol. Catal. A: Chem. 2014, 381, 61. doi: 10.1016/j.molcata.2013.10.008
7. [7]
  (7) Tao, F. F. Chem. Soc. Rev. 2012, 41, 7977. doi: 10.1039/c2cs90093a(7) Tao, F. F. Chem. Soc. Rev. 2012, 41, 7977. doi: 10.1039/c2cs90093a
8. [8]
  (8) Guczi, L.; Schay, Z.; Stefler, G.; Liotta, L. F.; Deganello, G.; Venezia, A. M. J. Catal. 1999, 182, 456. doi: 10.1006/jcat.1998.2344(8) Guczi, L.; Schay, Z.; Stefler, G.; Liotta, L. F.; Deganello, G.; Venezia, A. M. J. Catal. 1999, 182, 456. doi: 10.1006/jcat.1998.2344
9. [9]
  (9) Domínguez-Domínguez, S.; Berenguer-Murcia, Á.; Cazorla-Amorós, D.; Linares-Solano, Á. J. Catal. 2006, 243, 74. doi: 10.1016/j.jcat.2006.06.027(9) Domínguez-Domínguez, S.; Berenguer-Murcia, Á.; Cazorla-Amorós, D.; Linares-Solano, Á. J. Catal. 2006, 243, 74. doi: 10.1016/j.jcat.2006.06.027
10. [10]
  (10) Yoshida, H.; Zama, T.; Fujita, S.; Panpranot, J.; Arai, M. RSC Advances 2014, 4, 24922. doi: 10.1039/c4ra02220c(10) Yoshida, H.; Zama, T.; Fujita, S.; Panpranot, J.; Arai, M. RSC Advances 2014, 4, 24922. doi: 10.1039/c4ra02220c
11. [11]
  (11) Shao, Z.; Li, C.; Liang, C. H. J. Mol. Catal. 2014, 28, 47. [邵正锋, 李闯, 梁长海. 分子催化, 2014, 28, 47.](11) Shao, Z.; Li, C.; Liang, C. H. J. Mol. Catal. 2014, 28, 47. [邵正锋, 李闯, 梁长海. 分子催化, 2014, 28, 47.]
12. [12]
  (12) Kyriakou, G.; Boucher, M. B.; Jewell, A. D.; Lewis, E. A.; Lawton, T. J.; Baber, A. E.; Tierney, H. L.; Flytzani- Stephanopoulos, M.; Sykes, E. C. H. Science 2012, 335, 1209. doi: 10.1126/science.1215864(12) Kyriakou, G.; Boucher, M. B.; Jewell, A. D.; Lewis, E. A.; Lawton, T. J.; Baber, A. E.; Tierney, H. L.; Flytzani- Stephanopoulos, M.; Sykes, E. C. H. Science 2012, 335, 1209. doi: 10.1126/science.1215864
13. [13]
  (13) Boucher, M. B.; Zugic, B.; Cladaras, G.; Kammert, J.; Marcinkowski, M. D.; Lawton, T. J.; Sykes, E. C. H.; Flytzani-Stephanopoulos, M. Phys. Chem. Chem. Phys. 2013, 15, 12187. doi: 10.1039/c3cp51538a(13) Boucher, M. B.; Zugic, B.; Cladaras, G.; Kammert, J.; Marcinkowski, M. D.; Lawton, T. J.; Sykes, E. C. H.; Flytzani-Stephanopoulos, M. Phys. Chem. Chem. Phys. 2013, 15, 12187. doi: 10.1039/c3cp51538a
14. [14]
  (14) Kim, S. K.; Lee, J. H.; Ahn, I. Y.; Kim,W.; Moon, S. H. Appl. Catal. A 2011, 401, 12. doi: 10.1016/j.apcata.2011.04.048(14) Kim, S. K.; Lee, J. H.; Ahn, I. Y.; Kim,W.; Moon, S. H. Appl. Catal. A 2011, 401, 12. doi: 10.1016/j.apcata.2011.04.048
15. [15]
  (15) Weerachawanasak, P.; Mekasuwandumrong, O.; Arai, M.; Fujita, S.; Praserthdam, P.; Panpranot, J. J. Catal. 2009, 262, 199. doi: 10.1016/j.jcat.2008.12.011(15) Weerachawanasak, P.; Mekasuwandumrong, O.; Arai, M.; Fujita, S.; Praserthdam, P.; Panpranot, J. J. Catal. 2009, 262, 199. doi: 10.1016/j.jcat.2008.12.011
16. [16]
  (16) Molnár, Á.; Sárkány, A.; Varga, M. J. Mol. Catal. A: Chem. 2001, 173, 185. doi: 10.1016/S1381-1169(01)00150-9(16) Molnár, Á.; Sárkány, A.; Varga, M. J. Mol. Catal. A: Chem. 2001, 173, 185. doi: 10.1016/S1381-1169(01)00150-9
17. [17]
  (17) Shao, Z.; Li, C.; Chen, X.; Pang, M.;Wang, X.; Liang, C. ChemCatChem 2010, 2, 1555. doi: 10.1002/cctc.v2.12(17) Shao, Z.; Li, C.; Chen, X.; Pang, M.;Wang, X.; Liang, C. ChemCatChem 2010, 2, 1555. doi: 10.1002/cctc.v2.12
18. [18]
  (18) Mao, J.; Liu, Y.; Chen, Z.;Wang, D.; Li, Y. Chem. Commun. 2014, 50, 4588. doi: 10.1039/c4cc01051e(18) Mao, J.; Liu, Y.; Chen, Z.;Wang, D.; Li, Y. Chem. Commun. 2014, 50, 4588. doi: 10.1039/c4cc01051e
19. [19]
  (19) Sitthisa, S.; Pham, T.; Prasomsri, T.; Sooknoi, T.; Mallinson, R. G.; Resasco, D. E. J. Catal. 2011, 280, 17. doi: 10.1016/j.jcat.2011.02.006(19) Sitthisa, S.; Pham, T.; Prasomsri, T.; Sooknoi, T.; Mallinson, R. G.; Resasco, D. E. J. Catal. 2011, 280, 17. doi: 10.1016/j.jcat.2011.02.006
20. [20]
  (20) Jeroro, E.; Hyman, M. P.; Vohs, J. M. Phys. Chem. Chem. Phys. 2009, 11, 10457. doi: 10.1039/b913220a(20) Jeroro, E.; Hyman, M. P.; Vohs, J. M. Phys. Chem. Chem. Phys. 2009, 11, 10457. doi: 10.1039/b913220a
21. [21]
  (21) Pattamakomsan, K.; Ehret, E.; Morfin, F.; Gélin, P.; Jugnet, Y.; Prakash, S.; Bertolini, J. C.; Panpranot, J.; Aires, F. J. C. S. Catal. Today 2011, 164, 28. doi: 10.1016/j.cattod.2010.10.013(21) Pattamakomsan, K.; Ehret, E.; Morfin, F.; Gélin, P.; Jugnet, Y.; Prakash, S.; Bertolini, J. C.; Panpranot, J.; Aires, F. J. C. S. Catal. Today 2011, 164, 28. doi: 10.1016/j.cattod.2010.10.013
22. [22]
  (22) Venezia, A. M.; Liotta, L. F.; Deganello, G.; Schay, Z.; Guczi, L. J. Catal. 1999, 182, 449. doi: 10.1006/jcat.1998.2343(22) Venezia, A. M.; Liotta, L. F.; Deganello, G.; Schay, Z.; Guczi, L. J. Catal. 1999, 182, 449. doi: 10.1006/jcat.1998.2343
23. [23]
  (23) Skoda, F.; Astier, M. P.; Pajonk, G. M.; Primet, M. Catal. Lett. 1994, 29, 159.(23) Skoda, F.; Astier, M. P.; Pajonk, G. M.; Primet, M. Catal. Lett. 1994, 29, 159.
24. [24]
  (24) Strohmeier, B. R.; Levden, D. E.; Field, R. S.; Hercules, D. M. J. Catal. 1985, 94, 514. doi: 10.1016/0021-9517(85)90216-7(24) Strohmeier, B. R.; Levden, D. E.; Field, R. S.; Hercules, D. M. J. Catal. 1985, 94, 514. doi: 10.1016/0021-9517(85)90216-7
25. [25]
  (25) Leviness, S.; Nair, V.;Weiss, A. H.; Schay, Z.; Guczi, L. J. Mol. Catal. 1984, 25, 131. doi: 10.1016/0304-5102(84)80037-1
  (25) Leviness, S.; Nair, V.;Weiss, A. H.; Schay, Z.; Guczi, L. J. Mol. Catal. 1984, 25, 131. doi: 10.1016/0304-5102(84)80037-1

扫一扫看文章

计量

PDF下载量: 334
文章访问数: 647
HTML全文浏览量: 12

通讯作者: 陈斌, bchen63@163.com

1.
沈阳化工大学材料科学与工程学院沈阳 110142

Pd-Cu/γ-Al₂O₃催化苯乙炔选择性加氢反应

English

Selective Hydrogenation of Phenylacetylene over Pd-Cu/γ-Al₂O₃ Catalysts

CCS Chemistry：嵌段共聚物自组装成 “三明治”二维有机材料，实现纳米级压力传感功能

CCS Chemistry：颜徐州、鲍哲南：你的皮肤可能是一片SPMs

CCS Chemistry：工作高效不疲劳，只须让催化剂动起来

CCS Chemistry：静电组装导向聚合- 聚电解质纳米凝胶量化制备新策略

CCS Chemistry：金黄色葡萄球菌醛基脱氢酶是如何识别特异性底物的？

计量

通讯作者: 陈斌, bchen63@163.com

中国化学会秘书处